1V Prewired Harness, 2 Pickup HH/HS, Push-Pull Pot, 3W Sealed Switch
Click To Enlarge

1V Prewired Two Pickup Harness
Push Pull Coil Split Pot

Sealed Switch Wiring Harness
For HH, HS, or SH Standard Systems
Works Great for So-Cal /Charvel Styles
1 Push-Pull Volume Control Pot
3 Way Sealed Blade Switch ~ Standard Jack
Pre-Wired Electric Guitar Wiring Harness

These customized hand-wired Volume Pot Harnesses work well with most Two Pickup (i.e. Humbucker-Humbucker or Humbucker-Single) Systems. These single pot harnesses are designed for players seeking a minimized, uncluttered control field and are great for So-Cal / Charvel® Style systems. Each harness is unique and, based on order style/selections as well as current component stock on hand, will vary in appearance from the sample images. Read all product information carefully and ask any questions before you buy.

This prewired harness features the following default options. Your menu selections may vary and we will wire to order.
*1 Sealed 3 Way Blade Switch
*1 Push-Pull 500K Small/Long Volume Control Pot
*1 Standard Mono Style Jack
Customizable Options & Upgrades Available!

The Sealed 3-Way Blade Switch on this harness provides standard 3 Way pickup selections; this allows for Bridge/Bridge-Neck/Neck options.
These harnesses use push-pull small pots (dime size / mini pots) for coil splitting. These pots have long shafts for body mounting. If you are going through a guard or have a non-standard set-up, you may need additional nuts/washers (sold separately) or other modification. This style of pot will work with most coarse-knurled, 18-spline style knobs (sold separately). Audio Taper (“A” pot) or Linear Taper (“B” pot) styles are available.

The Coil Split Wiring incorporated into this harness allows you to split humbucker coils in half, cutting one coil out and allowing humbuckers to perform as single coils (also known as Coil Cut or Coil Tap). Four wire pickups are required for a coil split to work. For an HS, this coil split will only impact the humbucker. For an HH, this coil split will function simultaneously for both pickups.

Note that we do not recommend selecting a 250K pot for use with a push-pull coil tapping pot (exercise extreme discretion!). We provide the option to choose a North Coil (cuts the South and leaves only the North Coil engaged) or South Coil (cuts the North and leaves only the South engaged).

Harness jacks work with standard cables only and jack sockets accept standard ¼” plugs. Your choice of jack style:
*Mono Jack (9mm mounting hole; tightens to your jack plate)
*Stereo Jack (9mm mounting hole; tightens to your jack plate)
*Barrel Jack (12mm mounting hole; tightens inside of guitar)
*Switchcraft Jack (10mm mounting hole; tightens to jack plate)

Installation requires soldering. Basic instructions are posted in the item images to show the solder connections needed. Please know your abilities, requirements, measurements and needs to make sure this item will work for you. We are available to answer any questions before you buy.

We wire each harness to order and offer many style and upgrade options along with typical replacements in standard and left-handed versions. We can accommodate many styles and preferences. Check our Store Wiring Harness page or contact us for product variations or questions and additional options if needed.

*Switch Height: 48mm
*Switch Insertion Depth: 28.3mm
*Switch Dimensions: 48mm (length) x 13.5mm (width)
*Switch Screw Spacing (center:center): 41mm
*Pot Shaft Length: 18mm
*Pot Dimensions: 16.5mm (diameter) & 45mm (height)
*Pot Requirements: 10mm (hole diameter) & 28mm (depth)
*Standard Mono Jack Length: 15mm (without pins)
*Standard Mono Jack Diameter (Mounting Hole Required): 9mm
*8” Insulated Wire Length
Variability is to be expected as measurements provided are approximations and based on the default options. Options selected will determine actual measurements. Ask any questions regarding options, measurements, installation, requirements, special requests, etc. prior to purchase.

*1 Prewired Guitar Wiring Harness Kit
Nothing else is included. Additional images may be provided for reference and comparison purposes only. There are no hard copy instructions or diagrams included. Basic directions are provided in the product images.

OPTIONAL ADDITIONS (Further Customize Your Harness!)
The Kill Switch Wiring Option allows you to interrupt the signal using an on-off, two-way toggle style mini-switch (~5.85mm diameter; 6mm hole required).

The Treble Bleed Volume Kit Wiring Modifier addresses loss of high-end signal when turning down your volume pot to keep more of your highs while maintaining volume adjustability. This option allows a more constant tone throughout the range of your volume pot and helps remove the dark muddiness typically experienced in the lower volume pot settings.

Buyers assume all risk of use; sales are only offered to those competent to safely and lawfully purchase and use items. ASK ANY QUESTIONS PRIOR TO PURCHASE. Due to the vast and varied nature of possible set-ups and user expertise, we do not provide specific information for every possible installation scenario. The provided BASIC instructions (posted in the item images, not sent as a hard copy with your order) will get you started. Please ask any questions before you buy if the posted instructions are not sufficient for your install or if you are unsure of your needs or ability to make modifications.

Note that we do not recommend installation using power tools as these can put too much force on the product and cause damage. Installation is best with moderate heat only (don’t have your iron too hot). Pay attention during install to avoid damage; components are sensitive. Excessive or prolonged heat can cause irreparable damage. This item is prewired. If your set-up requires you to disconnect the wires, be sure to take a picture or make note of the connections so you can reattach (solder!) properly. We do not recommend a clip/tie method for installation.

Inspect your order upon receipt. We will address any issues PRIOR to installation. Installation, modification, or use in any way invalidates the possibility of a return.

  • Item #: 1050

1V Prewired 2 Pup Harness, PUSH-PULL CoilSplit, 3W Sealed Switch

Price: $29.95
* Marked fields are required.
Qty: *
Reviews (1) Write a Review
No Reviews. Write a Review